Number of units
The following data should also be added to Carrier LYNX API unit properties section of Wialon GPS tracking software :
| Device type: | Carrier LYNX API |
| Unique ID: | custom |
46 units of Carrier LYNX API device type are connected to Wialon Data Center. This represents 0.05% of all Protocols and retranslators connected.
Below chart represents the dynamic of connections in the last 30 days:
| Parameter name | Description | Units |
|---|---|---|
| pwr_on | powerStatus field in LYNX API Transport Refrigeration Unit Power Status (On or Off) |
|
| total_hours | switchOnHours field in LYNX API The total accumulated hours that the Transport Refrigeration Unit has been turned on |
|
| eng_hours | engineRunHours field in LYNX API The total accumulated hours that the Transport Refrigeration Unit has been running on its engine |
|
| tru_status | truStatus field in LYNX API Overall Status of the Transport Refrigeration Unit The following values are allowed:OFF, ON |
|
| hours_standby | standByHours field in LYNX API The total accumulated hours that the Transport Refrigeration Unit has been running on stand by, or electric, power |
|
| movement_status | movementStatus field in LYNX API Indicates if the unit is moving or not |
|
| eng_power_mode | enginePowerMode field in LYNX API Transport Refrigeration Unit Power Source (Engine or Standby) The following values are allowed:Standby, Engine |
|
| eng_ctrl_mode | engineControlMode field in LYNX API Transport Refrigeration Unit Control Mode The following values are allowed:Continuous, Start/Stop |
|
| eng_spd | engineSpeed field in LYNX API Transport Refrigeration Unit Engine Speed The following values are allowed:High, Low, Very Low, Very High |
rpm |
| ign | switchKeyStatus field in LYNX API Lcv switch key status |
|
| lcv_road_energy | roadEnergy field in LYNX API Lcv road energy |
kJ |
| lcv_standby_energy | StandByEnergy field in LYNX API Lcv standBy Energy |
kJ |
| lcv_pwr_mode | powerMode field in LYNX API Lcv power mode |
|
| pwr_int | batteryVoltage field in LYNX API The voltage of the Transport Refrigeration Unit's 12V battery |
V |
| pwr_cur | batteryCurrent field in LYNX API Battery Current (Device) |
mA |
| 1wire_temp[N] | oneWireTemp[NUM] field in LYNX API One Wire temperature of the [N] sensor |
°C |
| point_temp[N] | setpointTemp[N] field in LYNX API Compartment [N] Setpoint Temperature |
°C |
| bt_temp[N] | bluetoothTemp[N] field in LYNX API Bluetooth temperature sensor [N] |
°C |
| datacold_temp[0] | datacoldTemp[N] field in LYNX API DataCOLD temperature sensor [N] |
°C |
| ret_air_temp[N] | returnAirTemp[N] field in LYNX API Compartment [N] Return Air Temperature |
°C |
| supply_air_temp[N] | supplyAirTemp1 field in LYNX API Compartment [N] Supply Air Temperature |
°C |
| tenant_name | tenantName field in LYNX API Asset Company Name |
|
| ctrl_sys_type | truControlSystemType field in LYNX API Transport Refrigeration Unit - Control System Type |
|
| plate_number | licensePlateNumber field in LYNX API Asset License Plate |
|
| sf_vers | truSoftwareVersion field in LYNX API Transport Refrigeration Unit - Software Version |
|
| tru_model_num | truModelNumber field in LYNX API Transport Refrigeration Unit - Model Number |
|
| operat_mode[N] | comp[N]OperatingMode field in LYNX API Operating mode of Compartment [N] |
|
| fuel_lvl | fuelLevel field in LYNX API Transport Refrigeration Unit Fuel Level |
% |
| side_door | sideDoorOpen field in LYNX API ndicates if the side door on the truck or trailer is open or not |
|
| rear_door | rearDoorOpen field in LYNX API Indicates if the rear door on the truck or trailer is open or not |
|
| mileage | vehicleMileage field in LYNX API Mileage of the unit at the time of the message |
km |
| rssi | signalStrength field in LYNX API Signal Strength |
