report_type |
Report Type
|
|
rep_id |
Report ID
|
|
rep_type |
Report type (GT###)
|
|
mcc |
Mobile country code
|
|
mnc |
Mobile network code
|
|
lac |
Location area code in hex format
|
|
cell_id |
Cell ID in hex format |
|
mileage |
The current total mileage
|
|
hour_meter_count |
Hour Meter Count
|
h |
h_m_count |
Hour Meter Count
|
h |
battery |
Backup Battery Percentage
|
% |
ign |
Ignition status
|
|
motion_state |
Device status - 16 (Tow): The device attached vehicle is ignition off and it is towed.
- 1A (Fake Tow): The device attached vehicle is ignition off and it might be towed.
- 11 (Ignition Off Rest): The device attached vehicle is ignition off and it is motionless.
- 12 (Ignition Off Motion): The device attached vehicle is ignition off and it is moving before it is treated as being towed.
- 21 (Ignition On Rest): The device attached vehicle is ignition on and it is motion less
- 22 (Ignition On Motion): The device attached vehicle is ignition on and it is moving
- 41 (Sensor Rest): The device attached vehicle is motionless without ignition signal detected
- 42 (Sensor Motion): The device attached vehicle is moving without ignition signal detected
|
|
pwr_ext |
External Power Voltage |
|
iccid |
ICCID
|
|
csq_rssi |
- GSM signal level of the terminal
|
|
gsm |
GSM signal level of the terminal
|
|
csq_ber |
The quality of the GSM signal. The range is 0-7, 99 for unknown.
|
|
bat_status |
Whether the external power supply is connected. - 0: Not connected
- 1: Connected
|
|
charging |
Whether the backup battery is charging when the main power supply is connected. - 0: Not charging
- 1: Charging
|
|
led_on |
Indicate whether the LED’s are turned on:
|
|
din_status |
A bitwise hex integer to represents the logical status of the digital input. From the lowest bit to the highest bit, each bit represents ignition detection and one of the digital inputs 1 respectively. For each bit, 0 means disable status, 1 means enable status.
|
|
dout_status |
A bitwise hex integer to represents the logical status of the digital output. From the lowest bit to the highest bit, each bit represents one of the digital outputs 1 – 2 respectively. For each bit, 0 means disable status, 1 means enable status
|
|
time_zone |
The time offset of the local time zone to the UTC time. |
m |
daylight_saving |
The current setting of the daylight saving. - 0: Daylight saving is disabled
- 1: Daylight saving is enabled
|
|
data_type |
The data reported to backend server is recorded before or after crash. - 0: before crash.
- 1: after crash.
|
|
frames_count |
Total number of messages that are sent to the bckend server for the crash event.
|
|
frame |
A numeric to indicate the sequence of the current message.
|
|
x_axis# |
X axis acceleration data
|
|
y_axis# |
Y axis acceleration data
|
|
z_axis# |
Z axis acceleration data
|
|
ign_off_duration |
Duration of Ignition Off
|
s |
ign_on_duration |
Duration of Ignition On
|
s |
state |
The current motion state when the vehicle leaves idling status.
|
|
idle_dt |
The time that the vehicle has been in idling status.
|
s |
gps_signal_status |
GPS Signal Status: - 0 means lost GPS signal or no successful GPS fix,
- 1 means GPS signal recovered and successful GPS fix.
|
|
sats |
Satellite Number
|
|
wave1_out_id |
ID of the output With wave shape 1
|
|
wave1_out_active |
The output status with wave shape 1
|
|
roaming_state |
Roam state : - 0 Home
- 1 Known Roaming
- 2 Unknow Roaming
- 3 Blocking Report
|
|
jamming_status |
The current Jamming status of the device. - 1: Quit the jamming.
- 2: Enter the jamming.
|
|
jamming_cw |
Continuous wave(narrowband) jamming detection threshold |
dB |
jamming_gps |
Broadband jamming detection threshold
|
dB |
is_pwr_ext |
External Power Supply
|
|
mcu_ver |
MCU Version
|
|
hw_ver |
Hardware Version
|
|
fw_ver |
Firmware Version |
|