| msg_type_name |
Report type of the message
|
|
| buffer |
Shows if the message was buffered
+BUFF header = buffer: 1 +RESP header = buffer: 0
|
|
| mcc[NUM] |
Mobile country code of the base station [NUM]
|
|
| mnc[NUM] |
Mobile Network code of the base station [NUM]
|
|
| lac[NUM] |
Location area code of the base station [NUM]
|
|
| cell_id[NULL] |
Cell tower ID of the base station [NUM]
|
|
| rep_id |
- +RESP:GTGEO: indicates the ID of the Geo-Fence.
- For other messages, it is always 0.
|
|
| rep_type |
rep_type has several meanings for the different packages - +RESP:GTNMR
- +RESP:GTGEO
- +RESP:GTDOG
1 - Reboot device message for time based working mode. 2 - Reserved 3 - Reserved 4 - Reboot device message for network watchdog 5 - Reboot device message for EGPRS/LTE watchdog 6 - Reboot device message for send failure watchdog
- +RESP:GTFRI
- Always 0 - This message is a common scheduled position report.
|
|
| battery |
The current volume of the battery in percentage.
|
% |
| rf_radio_status |
Indicate status of the RF radio - 0 - RF433 is off
- 1 - RF433 is on
|
|
| rf_channel_freq |
A number to indicate the transmit channel frequency of the RF433.
|
MHz |
| rat |
Radio Access Technology. - 0 - NO SERVICE mode
- 1 - EGPRS mode
- 2 - Reserved
- 3 - Reserved
- 4 - LTE Cat1 mode
|
|
| band |
- 0 means invalid band
- 1-5/7-8/20/28 mean band number, and others mean GSM number.
|
|
| motion_status |
The current motion status of the device
- 0x41 (Sensor Rest) - The device attached vehicle is motionless without ignition signal detected.
- 0x42 (Sensor Motion) - The device attached vehicle is moving without ignition signal detected.
|
|
| iccid |
The ICCID of the SIM card.
|
|
| rx_level |
The signal strength level
| rx_level
|
⠀⠀⠀Signal Strength (dBm)
|
| 0
|
< -113
|
| 1
|
-111
|
| 2 - 30
|
-109 - -53
|
| 31
|
> -51
|
| 99
|
Unknown
|
| rx_level |
⠀⠀⠀Signal Strength (dBm) |
| 0 |
< -140 |
| 1 |
-140 |
| 2 - 96 |
-139 - -44 |
| 97 |
> -44 |
| 255 |
Unknown |
|
|
| rx_ber |
The quality of the GSM signal. The range is 0-7, and 99 is for unknown strength of signal
|
|
| network_type |
The type of the mobile network the device is currently registered on.
- 0 - Unregistered
- 1 - EGPRS
- 2 - Reserved
- 3 - LTE
|
|
| backup_battery_pwr |
The voltage of the backup battery. The value of this field is valid only when the external power is not connected.
|
V |
| charge |
Whether the backup battery is charging when the main power supply is connected. - 0 - Not charging.
- 1 - Charging.
|
|
| led_state |
A numeral to indicate the working status of all LED lights. - 1 - All LEDs turn on as configured.
- 2 - All LEDs work 5 minutes after powering on and then will be off. And all LEDs will work 5 minutes again after the power key is pressed shorter than 2 seconds.
|
|
| last_fix_tm |
The UTC time of the latest successful GNSS fix.
It has following format: HH:MM:SS DD/MM/YYYY
|
|
| time_zone |
Time zone offset from the UTC-0 Time
|
minutes |
| daylight_saving |
The current setting of the daylight saving. - 0 - Daylight saving is disabled.
- 1 - Daylight saving is enabled.
|
|
| device_type |
The type of the device
|
|
| fw_ver |
Firmware Version
|
|
| hw_ver |
Hardware Version
|
|
| network_tm_check |
A numeral to indicate whether to check GNSS UTC time with network time. - 0 - Only correct device time when the device can't get GNSS UTC time.
- 1 - Always correct device time with network time.
|
|
| total_packets |
Total packets of GTALM packages
|
|
| current_packet |
Current packet of GTALM package
|
|
| alm |
The full configuration of the device from +RESP:GTALM
|
|
| call_num |
The phone number of the incoming call which triggers the report message.
|
|
| report_composition_mask |
Bitwise mask to configure the composition of a report message, especially the composition of GNSS information. - Bit 0 - for <Speed>
- Bit 1 - for <Azimuth>
- Bit 2 - for <Altitude>
- Bit 3 - for Cell information, including <MCC>, <MNC>, <LAC>, <Cell ID>.
- Bit 4 - for <Send Time>, the time when the report message is generated.
- Bit 5 - for <Device Name>
For each bit, set it to 1 to enable the corresponding component in the report, and 0 to disable the corresponding component in the report. This mask is valid for all report messages. Bit3 is invalid for the +RESP:GTGSM message.
|
|
| sv_[ID] |
Satellite power of satellite [ID]. If there is no satellite, the field is filled with zero
|
|
| fix_type |
A string to indicate what kind of GNSS fix this cell information is for. - "RTL": This cell information is for RTL request.
- "FRI": This cell information is for FRI request.
- "GIR": This cell information is for the sub command "F" in the (AT+GTRTO) command.
|
|
| upd_code | eud_code |
+RESP:GTUPD It indicates the download information. 1x0 - The update command is confirmed by the device. 1x1 - The update command is refused by the device. 1x2 - The update process is cancelled by the backend server or refused because of an incorrect URL. 1x3 - The update process is refused because the external power supply is not inserted. 1x5 - The update process is refused because the upgraded unit is not working. - 2x0 - The device starts to download the package.
- 2x1 - The device finishes downloading the package successfully.
- 2x2 - The device fails to download the package.
- 3x0 - The device starts to update the firmware.
- 3x1 - The device finishes updating the firmware successfully.
- 3x2 - The device fails to update the firmware.
- 3x3 - The update process does not start because the battery is low.
- 3x4 - Serial Number does not match, firmware upgrade fails.
+RESP:GTEUD - 1x0 - The device confirms this update command.
- 1x1 - The device refuses this update command.
- 1x2 - The backend server cancels this update process.
- 1x3 - The device refuses this request because the battery is low.
- 1x4 - The update process is refused because the upgraded unit is not working.
- 2x0 - The device starts to download the package.
- 2x1 - The device downloads the package successfully.
- 2x2 - The device fails to download the package.
- 3x0 - The device starts to update the firmware.
- 3x1 - The device updates the firmware successfully.
- 3x2 - The device fails to update the firmware.
- 3x3 - The device cancels the firmware update because the battery is low.
- 3x4 - Serial Number does not match, firmware upgrade fails.
|
|
| download_times |
The count number of the package download.
|
|
| jamming_status |
The current jamming status of the device. - 1 - Quit the jamming state.
- 2 - Enter the jamming state.
|
|
| battery_pwr |
Battery Voltage
|
V |
| alm_type |
The type of temperature alarm. - 1 - The current temperature is lower than the lower temperature limit defined by <Min Temperature>.
- 2 - The current temperature is within the temperature threshold range specified by <Min Temperature> and <Max Temperature>.
- 3 - The current temperature is higher than the higher temperature limit defined by <Max Temperature>.
|
|
| temp |
The current temperature of the device.
|
|
| mode |
The working mode of file transfer
|
|
| protocol_type |
The type of communication protocol used to obtain data from the backend server
|
|
| file_type |
It defines the type of file to download from the server.
- 0 - CA certificate
- 1 - Client certificate
- 2 - Client key
|
|
| rtp_code |
It indicates the download information. - 100 - The update command is starting.
- 101 - The update command is refused by the device.
- 200 - The device starts to download the file.
- 201 - The device finishes downloading the file successfully.
- 202 - The device fails to download the file.
- 301 - The device finishes updating the file successfully.
- 302 - The device fails to update the file
|
|
| ident_num |
Identifier Number A numeral to identify the firmware update request. It will be included in the +RESP:GTEUD message to indicate the request it is related to.
|
|
| dev_type |
Device type: Always 0x128 for Queclink GL33CG
|
|
| gps_acc |
GNSS Accuracy A numeral to indicate the GNSS fix status and HDOP of the GNSS position. - 0 means the current GNSS fix fails and the last known GNSS position is used.
- A non-zero value (1 - 50) means the current GNSS fix is successful and represents the HDOP of the current GNSS position.
|
|
