GPS tracker Meitrack T633L | Integrated with Wialon

The following data should also be added to Meitrack T633L unit properties section of Wialon GPS tracking software :

Device type:	Meitrack T633L
Unique ID:	imei

Specify the following parameters in configuration software or configuration Meitrack T633L for use in Wialon Hosting :

Server port:

21910

899 units of Meitrack T633L device type are connected to Wialon Data Center. This represents 0.04% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
RFID	RFID code
event_code	Event Code
valid	GPS status
gsm_signal	GSM signal
hdop	Horizontal Dilution of Precision
mileage	Total accumulated mileage	km
engine_hours	Total accumulated runtime
battery	battery charge	V
pwr_ext	Voltage of external power supply	V
fuel_percent	Percentage of remain fuel	%
temp_N	Temperature sensor N value	°C
wln_accel_max	Maximum acceleration value	g
wln_brk_max	Maximum deceleration value	g
lls_N_temp	LLS fuel sensor N temperature	°C
lls_N_val	LLS fuel sensor value
lls_N_freq	LLS fuel sensor frequency
dr_f_status	Driver fatigue alert: 01 - Mild fatigue 02 - Moderate fatigue 03 - Severe fatigue 04 - Distraction alert 05 - Absence alert 06 - On Phone Call alert 07 - Smoking alert 08 - Yawning alert
ignition	Ignition status
tire{tire_id}_loc	Tire position Tire position：7~5bit indicate the vehicle head or trailer：000(B): Vehicle head， 001(B):Trailer 1，010(B): Trailer 2， 011(B): Trailer 3，100(B): Trailer 4， 4~0bit indicate the tire number：For example, 00001(B), indicating the first tire
tire{tire_id}_press	Tire pressure value: Formula :obtained value x 0.025	bar
tire{tire_id}_temp	Tire temperature value: Formula: obtained value – 50	°C
tire{tire_id}_alert	Tire status: Bit7: indicates the battery voltage status of the transmitter. 0: normal voltage; 1: low voltage. Bit6：Whether to receive data from the transmitter. If you do not receive data from the transmitter within 15 minutes, the parameter value will be reset to 1. Bit5：reserved. Bit4：When the value is 1, the air pressure is high. Bit3：When the value is 1, the air pressure is low Bit2：indicates temperature status. 1: high temperature; 0: normal temperature. Bit1~Bit0：indicates the alert status. 00: no alert; 01: fast air leak alert; 10: slow air leak alert; 11: tire inflation alert.
system_flag	System Flag: Bit 0: Whether to modify the EEP2 parameter. When the parameter value is 1, the EEP2 parameter is modified. Bit 1: Indicates the ACC status. When the parameter value is 1, the ACC is on. Bit 2: Indicates the anti-theft status. When the parameter value is 1, the tracker is in the arming state. Bit 3: vibration flag. When the parameter value is 1, the tracker is vibrating. Bit 4: moving flag. When the parameter value is 1, the tracker is moving. Bit 5: Whether to connect the external power supply. When the parameter value is 1, the external power supply is connected. Bit 6: Whether the tracker is charging. When the parameter value is 1, the tracker is charging. Bit 7: Whether to enable the sleep mode. When the parameter value is 1, the sleep mode is enabled. Bit 8: Whether to connect the FMS. When the parameter value is 1, the FMS is connected. Bit 9: Whether to enable the FMS function. When the parameter value is 1, the function is enabled. Bit 10: Whether to connect the Mobileye. When the parameter value is 1, the Mobileye is disconnected. Bit 11: Whether to connect the Mobileye. When the parameter value is 1, the Mobileye is connected. Bits 12–31: reserved.
outputs_status	Indicates the status values of eight output ports. Bits 0–7 correspond to status of output ports 1–8.
geo_fance_number	Number of Geo-fence
clutch_switch	Clutch switch: 0: The clutch pedal is released 1: The clutch pedal is pressed.
park_brake	Parking brake switch: 0: Do not apply the brake. 1: Apply the brake.
cruise_cnt	Cruise control system: 0: The cruise control system is switched off. 1: The cruise control system is switched on.
acc_pedal	Accelerator pedal position	%
can_fuel_lvl	CAN bus fuel level	%
fuel_level_proc	Fuel level, should be divided by 100	%
veh_speed_taho	Vehicle speed (based on the tachograph)	km/h
veh_speed_wheel	Vehicle speed (based on the wheel)	km/h
engine_speed	Engine speed	rpm
eng_cool_temp	Engine coolant temperature	°C
run_time	Run time	h
total_fuel_cons	Total fuel consumption	l
total_eng_run_tm	Total engine run time	h
high_res_veh_dist	High resolution vehicle distance	m
service_dist	Service distance	km
axle_weight	Axle weight	kg
sens{ind_sens}	Temperature sensor {ind_sens} value	°C
accel_x	Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered	mg
accel_y	Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered	mg
accel_z	Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered	mg
taho_perf	Tachograph performance: 0: normal performance 1: performance analysis
act_eng_torque	Actual engine torque	%
act_eng_tor_speed	Actual engine torque at current speed	%
amb_air_temp	Ambient air temperature	°C
in_port_status	Input port status Bits 0–31 correspond to status of input ports 1–31.When the parameter value is 0, the port is inactive. When the parameter value is 1, the port is active.
netw_id	Network ID
netw_ver	Network version
netw_type	Network type： 0: No Network, 1: Mobile Network, 2: WIFI (Reserved), 3: LAN (Reserved)
netw_descr	Network descriptor

Parameter name

Description

Units

RFID

RFID code

event_code

Event Code

valid

GPS status

gsm_signal

GSM signal

hdop

Horizontal Dilution of Precision

mileage

Total accumulated mileage

engine_hours

Total accumulated runtime

battery

battery charge

pwr_ext

Voltage of external power supply

fuel_percent

Percentage of remain fuel

temp_N

Temperature sensor N value

°C

wln_accel_max

Maximum acceleration value

wln_brk_max

Maximum deceleration value

lls_N_temp

LLS fuel sensor N temperature

°C

lls_N_val

LLS fuel sensor value

lls_N_freq

LLS fuel sensor frequency

dr_f_status

Driver fatigue alert:

01 - Mild fatigue
02 - Moderate fatigue
03 - Severe fatigue
04 - Distraction alert
05 - Absence alert
06 - On Phone Call alert
07 - Smoking alert
08 - Yawning alert

ignition

Ignition status

tire{tire_id}_loc

Tire position
Tire position：7~5bit indicate the vehicle head or trailer：000(B): Vehicle head， 001(B):Trailer 1，010(B): Trailer 2， 011(B): Trailer 3，100(B): Trailer 4， 4~0bit indicate the tire number：For example, 00001(B), indicating the first tire

tire{tire_id}_press

Tire pressure value:
Formula :obtained value x 0.025

bar

tire{tire_id}_temp

Tire temperature value:
Formula: obtained value – 50

°C

tire{tire_id}_alert

Tire status:
Bit7: indicates the battery voltage status of the transmitter. 0: normal voltage; 1: low voltage.
Bit6：Whether to receive data from the transmitter. If you do not receive data from the transmitter within 15 minutes, the parameter value will be reset to 1. Bit5：reserved.
Bit4：When the value is 1, the air pressure is high.
Bit3：When the value is 1, the air pressure is low
Bit2：indicates temperature status. 1: high temperature; 0: normal temperature.
Bit1~Bit0：indicates the alert status. 00: no alert; 01: fast air leak alert; 10: slow air leak alert; 11: tire inflation alert.

system_flag

System Flag:
Bit 0: Whether to modify the EEP2 parameter. When the parameter value is 1, the EEP2 parameter is modified.
Bit 1: Indicates the ACC status. When the parameter value is 1, the ACC is on. Bit 2: Indicates the anti-theft status. When the parameter value is 1, the tracker is in the arming state.
Bit 3: vibration flag. When the parameter value is 1, the tracker is vibrating.
Bit 4: moving flag. When the parameter value is 1, the tracker is moving.
Bit 5: Whether to connect the external power supply. When the parameter value is 1, the external power supply is connected.
Bit 6: Whether the tracker is charging. When the parameter value is 1, the tracker is charging.
Bit 7: Whether to enable the sleep mode. When the parameter value is 1, the sleep mode is enabled.
Bit 8: Whether to connect the FMS. When the parameter value is 1, the FMS is connected.
Bit 9: Whether to enable the FMS function. When the parameter value is 1, the function is enabled.
Bit 10: Whether to connect the Mobileye. When the parameter value is 1, the Mobileye is disconnected.
Bit 11: Whether to connect the Mobileye. When the parameter value is 1, the Mobileye is connected.
Bits 12–31: reserved.

outputs_status

Indicates the status values of eight output ports. Bits 0–7 correspond to status of output ports 1–8.

geo_fance_number

Number of Geo-fence

clutch_switch

Clutch switch:
0: The clutch pedal is released
1: The clutch pedal is pressed.

park_brake

Parking brake switch:
0: Do not apply the brake.
1: Apply the brake.

cruise_cnt

Cruise control system:
0: The cruise control system is switched off.
1: The cruise control system is switched on.

acc_pedal

Accelerator pedal position

can_fuel_lvl

CAN bus fuel level

fuel_level_proc

Fuel level, should be divided by 100

veh_speed_taho

Vehicle speed (based on the tachograph)

km/h

veh_speed_wheel

Vehicle speed (based on the wheel)

km/h

engine_speed

Engine speed

rpm

eng_cool_temp

Engine coolant temperature

°C

run_time

Run time

total_fuel_cons

Total fuel consumption

total_eng_run_tm

Total engine run time

high_res_veh_dist

High resolution vehicle distance

service_dist

Service distance

axle_weight

Axle weight

sens{ind_sens}

Temperature sensor {ind_sens} value

°C

accel_x

Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered

accel_y

Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered

accel_z

Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered

taho_perf

Tachograph performance:
0: normal performance
1: performance analysis

act_eng_torque

Actual engine torque

act_eng_tor_speed

Actual engine torque at current speed

amb_air_temp

Ambient air temperature

°C

in_port_status

Input port status
Bits 0–31 correspond to status of input ports 1–31.When the parameter value is 0, the port is inactive. When the parameter value is 1, the port is active.

netw_id

Network ID

netw_ver

Network version

netw_type

Network type：
0: No Network,
1: Mobile Network,
2: WIFI (Reserved),
3: LAN (Reserved)

netw_descr

Network descriptor

Fill out a request form to get started with Wialon